Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Here down the page you will find a good deal of sensible information on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a new one is likewise a moderately tough project. If the old bathtub is readily accessible, the task can move immediately; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and embeded in the new one. Make sure you have certified on your own for the job and fit attempting it. Instead of employing a professional to take over a halfway-completed project, it is better to consider employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This article will certainly help you mount a new bathtub in your washroom if you have actually already purchased a new bathtub and also do not need to alter the plan of your previous water pipes.
Your tools and material checklist ought to comprise the following:
Planning for the Setup
To start with, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the tub until the level checks out level.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Activate the supply of water and inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill the bath tub as well as likewise examine the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub should wait until the bathtub has been utilized at least once as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in location between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a stiff seal, triggering the water to pass through the wall surface in between the bath and also the tiling, causing problems with dampness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are offered in tubes as well as cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealant can crack fairly early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that editorial on Installing A Bathtub through an associate on our other web blog. If you enjoyed our page if you please do not forget to share it. Thanks for your time. Don't hesitate to check our blog back soon.
Reliable round-the-clock. Report this page